Technical Papers and Presentations

Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.

On the Convergence Order of COMSOL Solutions

A. Bradji1, and E. Holzbecher2
1Charles University, Prague, Czech Republic
2Weierstrass Institute for Applied Analysis and Stochastics WIAS, Berlin, Germany

The convergence of numerical solutions is mainly determined by the convergence order, which quantifies the improvement of the solution when the mesh is refined. In this paper we examine various differential equations and the convergence behavior of their COMSOL Finite Element solutions. The numerically observed convergence rates are compared with theoretical results, as far as these are ...

Design of Pressure Measuring Cells Using the Unified Material Law

P. Aguirre[1], F. Figueroa[1]
[1]Sensor Technik Wiedemann GmbH, Kaufbeuren, Bayern, Germany

Pressure Sensors are widely used in the automotive industry. Their main use is the dynamic monitoring of pressure inside combustion engines. To achieve a good signal accuracy, the design of pressure sensors can be improved with FEM calculations of stress and strains on the measuring cell depending on their geometry and material properties. The geometry is adapted according to a special ...

Multiphysics Modeling of Warm-Air Drying of Potatoes Slices

S. Sandoval Torres[1], A. de Lourdes Allier González[1], L.L. Méndez Lagunas[1]
[1]Instituto Politécnico Nacional, CIIDIR, Oaxaca, Mexico

In this work we solve a model to simulate the drying of potatoes slices. The model considers both the transport of free and vapor water by applying a mechanistic approach. The critical moisture point (CMP) was considered, since it is a transition zone and it represents the point where water saturation is near from cero and hygroscopic domain begins. The CMP divides the hygroscopic and ...

Harmonic Simulation of Viscoelastic Polymer Microcantilever for Electrostrictive Energy Harvesters

N. Alcheikh[1], C. Ayela[1], I. Dufour[1]
[1]Univ. Bordeaux, IMS Lab, Pessac, France.

Electrostrictive polymers have been of significant interest over the last years for energy harvesting. Principle is based on the conversion of a mechanical deformation into electricity. The stored energy basically depends on the mechanical strain induced into an electrostrictive polymer by the mechanical resonant vibration of a microcantilever supporting the electrostrictive layer. In this work, ...

Simulating Organogenesis in COMSOL Multiphysics®: Parameter Optimization for PDE-based Models

D. Iber[1], D. Menshykau[2], P. Germann[2], L. Lermuzeaux[2,3]
[1]D-BSSE, ETH Zurich, Switzerland, SIB, Basel, Switzerland
[2]D-BSSE, ETH Zurich, Basel, Switzerland
[3]Department of Bioengineering, University of Nice-Sophia Antipolis, Nice, France

Morphogenesis is a tightly regulated process that has been studied for decades. Previously we developed data-based mechanistic models for a range of developmental processes with a view to integrate the available knowledge and to better understand the underlying regulatory logic. In our previous papers on simulating organogenesis in COMSOL Multiphysics® we discussed methods to efficiently solve ...

Simulation Organogenesis in COMSOL: Deforming and Interacting Domains

D. Iber[1], D. Menshykau[1]
[1]D-BSSE, ETH Zurich, Basel, Switzerland

Organogenesis is a tightly regulated process that has been studied experimentally for decades. We are developing mechanistic models for the morphogenesis of limbs, lungs, and kidneys with a view to integrate available knowledge and to better understand the underlying regulatory logic. Organ size changes dramatically during development, and tissues are composed of several layers that may expand ...

Early Stage Melt Ejection in Laser Percussion Drilling

T. Eppes[1]
[1]University of Hartford, Hartford, CT, USA

Laser percussion drilling is widely used in the aerospace industry to produce cooling holes in jet engine components. This process is a thermal, contact-free process which involves firing a sequence of focused optical pulses onto a target material [1-4]. During each optical pulse, the central portion of the target area heats to a liquid then vapor state where the expanding gas produces a recoil ...

Integrating COMSOL into a Mathematical Modeling Course for Chemical Engineers

A. Dixon, and D. DiBiasio
Department of Chemical Engineering, Worcester Polytechnic Institute, Worcester, MA, USA

The multiphysics simulation package COMSOL was incorporated into a course in mathematical modeling for chemical engineers. Our implementation for the first year of using COMSOL in the course is described, and assessment results based on examinations and student survey results are presented and analyzed. The students appear to be learning how to operate the COMSOL program quite satisfactorily, but ...

Utilization of COMSOL Multiphysics' JAVA API for the Implementation of a Micromagnetic Modeling and Simulation Package with a Customized User Interface

L. Teich[1], A. Hütten[2], C. Schröder[1]
[1]Department of Engineering Sciences and Mathematics, Computational Materials Science & Engineering (CMSE), University of Applied Sciences Bielefeld, Bielefeld, Germany
[2]Department of Physics, Thin Films and Nanostructures, Bielefeld University, Bielefeld, Germany

One of the big advantages of COMSOL Multiphysics is the possibility to implement user-defined partial differential equations (PDE) which can be coupled to COMSOL\'s predefined physics interfaces. However, using the tool’s standard user interface requires manual implementation of the PDEs and a multitude of problem-specific parameters. This process is not just error-prone but also very time ...

The Influence of Core Shape and Material Nonlinearities to Corner Losses of Inductive Element

M. Puskarczyk[1], B. Jamieson[1], W. Jurczak[1]
[1]ABB Corporate Research Center, Kraków, Poland

The effects of sharp corners on the flux distribution in a ferromagnetic core are modeled using COMSOL Multiphysics® to determine the time-domain flux density for an applied field which is uniform in the non-corner section of the core. The frequency spectrum of the flux distribution is calculated for testing points through the corner and the effects of harmonic frequencies on the flux and loss ...

Quick Search