C. Strozzi, P. Gillard, and J-M. Pascaud
Institut PRISME, Bourges, France
The aim of this work is to present a simple multiphysics simulation using COMSOL able to describe combustion of kerosene vapours in a closed vessel. The emphasis is on the mechanical effects of the reactive processes. The evolution of the thermodynamical variables (pressure, temperature, concentrations…) is obtained by solving several coupled transport equations for: the mass continuity, the ...
J. Muñoz, R. Valencia, and C. Nieto 
 Semillero Termodinámica y Fluidos, Universidad Pontificia Bolivariana, Medellin, Antioquia, Colombia
 Grupo Automática y Diseño
 Instituto de Energía y Termodinámica, Mechanical Engineering Faculty, Universidad Pontificia Bolivariana, Medellin, Antioquia, Colombia
Genetic Algorithms (GA) have proved to be a complete and effective approach for solving optimization problems. This article presents the integration between COMSOL® and a GA optimization tool coded in MATLAB® for the optimization of two thermal systems: a constant area fin in 2D and a concentric heat exchanger in 2D. Analysis permitted us to achieve efficiencies of up to 90%. For the ...
X. Gong, R. Wan
University of Calgary, Calgary, AB, Canada
THM (Thermo-Hydro-Mechanical) behavior of the reservoir during SAGD (Steam-Assistant-Gravity-Drainage) was studied through a proper constitutive modeling of the porous media. Specifically, a generalized density-stress-fabric dependent elasto-plastic model with stress-dilatancy and plastic damage as main ingredients was implemented into COMSOL Multiphysics®, to model geomechanical behavior during ...
S. Pramanik, M. Mishra
Indian Institute of Technology Ropar, Rupnagar, Punjab, India
Viscous fingering (VF) instability has been extensively studied over past several decades in the context of various industrial, environmental and chemical processes. We try to model miscible VF at pushed or pulled interfaces using COMSOL Multiphysics®. We study the effect of the positive and negative log-mobility ratio on the fingering instability. Numerical simulation has been performed in 2D ...
A.E. Varela, and J.C. García
University of Carabobo, Valencia, Venezuela
Most reactor designs are based on pseudo homogeneous models. This paper studies the COMSOL simulation of a packed bed reactor using a 2-D heterogeneous model. The case considered was a packed reactor with spherical catalyst for oxidation of o-xylene in air to phthalic anhydride. Large differences in intra-pellet temperature were found in comparison with the average temperatures resulting from ...
E. Gutierrez-Miravete, B. Fontenault
Rensselaer Polytechnic Institute, Hartford, CT, USA
General Dynamics-Electric Boat, Groton, CT, USA
A novel combined photovoltaic-thermal panel can simultaneously increase the conversion efficiency of the PV cell and utilize some of the excess thermal energy created by the conversion process (see Figure 1). The Conjugate Heat Transfer physics in COMSOL was used to create a two-dimensional, steady state model of such a combined photovoltaic cell-thermal panel. Figure 2 shows a magnified view of ...
Rensselaer Polytechnic Institute, Troy, NY, USA
A model was developed to simulate the reaction, concentration field, flow field, and temperature distribution inside a Claus reactor for converting hydrogen sulfide to sulfur. The model considered two ideal reactors, a continuous stirred tank reactor and a plug flow reactor. As expected, two ideal reactors showed much different behaviors in terms of reactant conversion and operating temperature. ...
P. Nakielski, T. Kowalczyk, T.A. Kowalewski
Institute of Fundamental Technological Research Polish Academy of Sciences, Warsaw, Poland
Comprehensive studies of drug transport in nanofibres based mats have been performed to predict drug release kinetics. The paper presents our approach to analyze the impact of fibers arrangement, one of the parameters varied in our parallel experimental studies. COMSOL Multiphysics® has been used to assess the impact of the various purposed arrangements of fibers within the mat. Drug release ...
B. Chinè, M. Monno, E. Repossi, M. Verani
Laboratorio MUSP Piacenza, Italy; ITCR, Esc. Ciencia e Ing. Materiales, Cartago, Costa Rica
Laboratorio MUSP, Piacenza, Italy; Politecnico di Milano, Dip. Meccanica, Milano, Italy
Politecnico di Milano, MOX-Dip. Matematica, Milano, Italy
The foaming process of a metal is a complex operation which needs to be closely controlled in order to guarantee the wanted properties, by avoiding the formation of defects in the structure of the material. In this work we use COMSOL Multiphysics® version 4.3b and apply the diffuse interface methods of the phase field technique available in the CFD module.To analyze a practical case, foams ...
G. Madabattula, S. K. Gupta
Department of Chemical Engineering, Indian Institute of Science, Bangalore, Karnataka, India
Low cost high energy density batteries that can be charged and discharged rapidly are required in a number of applications. Tapping energy from renewal resources such as solar, wind and tide requires rapidly generated energy to be first stored and then used round the clock. Storing energy of a moving vehicle as it slows down and recovering it to accelerate the vehicle later can significantly ...