M. Xu, Z. Wu, X. Wang
Tsinghua University, Beijing, China
Capillary effects are common in microfluidics due to large surface-to-volume ratio of flows inside microchannels. In biological or chemical analysis, capillary flow is used for the transport of liquid and mixing enhancement, without applying any external means. It’s used in biochemical analysis, drug delivery, and protein crystallization, where minute amount of liquids are precisely guided ...
A. Polit, R. Jez
ABB Corporate Research Center, Krakow, Poland
The air gap is one of the most crucial part of magnetic circuits, especially in high-power inductors. It significantly modifies the parameters of magnetic devices by increasing the saturation current, linearizing B-H curve of magnetic circuit and causing a decreasing in the inductance. Therefore the optimal selection of shape and dimensions of the air gap is very important from the design point ...
J. Crompton, S. Yushanov, K. Koppenhoefer
AltaSim Technologies, Columbus, OH, USA
The Mie solution to the scattering of electromagnetic waves by spherical particles has been examined using COMSOL Multiphysics®. The results assume elastic scattering only and do not include Brillouin or Raman scattering. The nature of the interaction has been considered for materials with three different properties: metallic, magnetic and dielectric. The solutions provide details of the ...
G. Atmeh, F. Darwish, and Z. Hasan
Jordan University of Science and Technology, Irbid, Jordan
Texas A&M University, College Station, TX, USA
The present study focuses on the design and analysis of a single-engine, propeller-driven general aviation airplane. Initial weight estimation based on the initial sketch and the design mission profile is conducted. The estimated weight and other design parameters are used to define the external geometry of the fuselage, wing and tail. Conic lofting is utilized to render a layout of the design ...
O. Vogel, and J. Ulm
Proportional solenoids are well-known and used in a wide range of applications today. This paper is about methods of influencing the characteristic force-stroke-curves of magnetic actuators by means of different pole geometries. The conical design of the stator pole which is mostly used to accomplish proportional solenoids is analyzed by both a simple analytic reluctance model and a FEM model ...
Multiphysics Simulation of Thermoelectric Systems - Modeling of Peltier-Cooling and Thermoelectric Generation
Fraunhofer-Institute for Physical Measurement-Techniques (IPM), Freiburg, Germany
Electro-thermal interaction is commonly considered only as a matter of joule heating. In addition, the Seebeck-, Peltier- and Thompson-Effects are significant in materials with high thermoelectric figure of merit Z. These thermoelectric materials have a high Seebeck-coefficient α, a good electric conductivity σ, and a poor thermal conductivity λ. They have widespread areas of ...
K. Al-Shurman, H. Naseem
The Institute for Nanoscience & Engineering, University of Arkansas, Fayetteville, AR, USA
Department of Electrical Engineering, University of Arkansas, Fayetteville, AR, USA
Chemical vapor deposition is considered a promising method for synthesis of graphene films on different types of substrate utilizing transition metals such as Ni. However, synthesizing a single-layer graphene and controlling the quality of the graphene CVD film on Ni are very challenging due to the multiplicity of the CVD growth conditions. COMSOL Multiphysics® software is used to investigate ...
Ravindra Mane, Sandeep soni
Department of Mechanical Engineering, Sardar Vallabhbhai National Institute of Technology, Surat, Gujarat, India
This paper presents the 3D model of hydrodynamic plain journal bearing using COMSOL Multiphysics®. Using 3D Model, pressure distribution in plain journal bearing is obtained by steady state analysis of plain journal bearing. Generalized Reynolds equation is used for analyzing hydrodynamic journal bearing by COMSOL Multiphysics® as well as by analytical method by applying Sommerfeld boundary ...
G. R. Prakash, K. M. V. Swamy, S. Huddar, B. G. Sheeparamatti, Kirankumar B. B.
Basaveshwar Engineering College, Bagalkot, Karnataka, India
The focus of this paper is to study the effect on resonance frequency and power enhancement techniques of piezoelectric MEMS and modeling, design, and optimization of a piezoelectric generator based on a two-layer bending element(Figure 1) using COMSOL Multiphysics. An analytical relation was developed based on the shift in resonance frequency(Figure 2) caused by the addition of a thin film ...
 Alpha Project Service, Vadodara, Gujarat, India
The interaction of a single particle in straight rectangular channel in laminar flow is modelled explicitly using the set of Navier Stokes equation for the fluid motion and Newton momentum equation for the particle motion in Cartesian coordinate system. The evaluation of integral force acting on the particle along with the behaviour of streamlines as a function of Reynolds number ReP < 120 is ...